Plan

Chicken Tractor Plans – Part 3

Jason Chicken, Infrastructure, Poultry , , , , ,

Last year I had to add detail to my parts list, which lead me to create the below outline and part list.  If you’re familiar with carpentry,  you should be able to take this blog and build a very sturdy and versatile chicken tractor.   Add this post to the basic diagrams in my earlier two posts, part 1 and part 2, and enjoy.

That’s not all.  This outline inspired me to write a 75+ page step by step how-to guide with illustrations, additional information, and personal experiences.  If you would like this detailed how-to guide, CLICK HERE.

As always, thank you for checking us out and all your support by liking and  sharing.

 

Supply List with  details.

Main Items

      • 3 – 16’x50” cattle/feedlot panels
        • Form the “hoop” structure Slightly overlapped
        • May want to cut one rung off end to shorten it so tarp can be stapled wood base easier.   Tarps come a little short because the measurements are raw not finished.
      • 5 – 2x4x12 treated
        • 2 – 12′ base sides
        • 2  – Cut 10′ base ends – 2′ extras become door diagonal supports
        • 1 – Cut 43″ for door frame top & cut 2 – 50″ sections  for back diagonals
      • 1 – 2x4x10
        • 1 – Cut 2 – 59″ door frame sides
      • 4 – 2x4x8 treated (3 if using 2×2 back upright)
        • 1 –  cut into 2′ lengths for corner braces for bottom frame
        • 2 – Rip in half to use for door
          • Or use 4 2x2x8 furring strips, but should stain them if not treated
          • Gives 4 2x2x8
            • 1 –  cut into 55″ and 31.5″ for side and top of door
            • 1 –  cut into 55″ and 31.5″ for side and bottom of door
            • 1 –  cut into 31.5 for middle brace on door
            • 1 – (optional) cut 61″ for back upright instead of using a 2×4
        • 1 – Cut 61″ for back upright
      • 75’ – 4’ Chicken wire
        • 50′ for 3 passes over the cattle pannels
        • 20′ for the ends
      • 50’ – 2′  hardware cloth, ¼” mesh
        • Perimeter of entire house.  Critter protection.
      • 20’ – 3’ 2×4 wire fence
        • Put over ends of coop for K-9 protection
      • 2 ½ – 3′ x  5-7′ scrap for back end weather board to give extra shelter
        • Should be fairly light
          • Thin pallet wood, what I used.
          • Sheet of tin roof
          • 1/4-1/2″ plywood or OSB
      • 12×16′ medium duty tarp, or heavy duty if you prefer.  Note the extra gets wrapped around the ends
      • 2 – 3” hinges
      • 2 – bolt latches
      • 1 – handle
      • 1 – large bag of zip ties. Used to fasten all the chicken wire, hardware cloth, fence, and cattle panels together.  So you want plenty.

Misc. Hardware

      • 2 – 3” hinges
      • 2 – bolt latches
      • 1 – handle
      • 24 – 3-3.5″ Lag screws. To assemble base, including corner supports
      • ~26 – 3″ deck screws.  To assemble door & frame and back upright and diagonals
      • 1/2-3/4″ Staples for staple gun
      • ~32 – 1 3/4″ Galvanized Fence staples.  To attach the cattle panels to the base and anchor the door and back upright.
      • Fasteners to attach the back weather break that won’t penetrate the 2×4 it’s going into.
        • 1 1/4 – 1 1/2 16GA staples (pneumatic stapler)
        • 1 1/2 – 1 3/4″ screw (Better than hand nails)
        • 3d-4d nail (d=penny)
      • 12’x16′ medium or heavy duty tarp.

Optional Apron

      • Ends
        • 25’ – 2′  ¼” hardware cloth
          • Will actually use approximately 12′, 1′ overlap on the ends.
        • 2 – 1 1/4″ x 10′ PVC pipe
        • For front and rear aprons
      • Sides
        • 25’ – 2′  ¼” hardware cloth (Can us e leftover from front and back apron if only 12′ was used for ends)
          • Will use approximately 13-14′.  Thirteen feet will give a 6″ overlap of the front and back apron while using just 1- 25′ roll of hardware cloth.
        • 3 – 1 1/4″ x 10′ PVC pipe
        • 2 – 1 1/4 PVC coupling

 

How I build the chicken tractors. 

    1. Start with the 10×12′ frame.  The 10′ end pieces should be raised about an inch to help pull the tractor over clumps of grass.
    1. Add diagonal corner braces.
    1. Hoop 3 sections of cattle panels.  They will overlap slightly. Nail them to the base and wire tie hoop sections together
    1. Assemble the door.
    1. Cut the door frame and attach to base and hoop with screws and fence nails.
    1. Cut and assemble the door.  I wait to attach it after I’ve stapled the chicken wire to the door.
    1. Put in rear vertical attaching the top to the hoop with fence nails.  Attach the diagonal supports.
      1. Add your end material for additional shelter.  Note: This side of the tractor will go to the most windward side, west for me.  The upper section is just covered by the tarp and can be raised for additional air flow. (don’t attach tarp yet)
    1. Cover the hoop with chicken wire, 3 passes of 4′.  Overlap slightly. Staple to wood frame and zip tie together and to the hoop.  I use a pneumatic staple gun with 5/8 staples, but a hand stapler should work fine, especially if you use a hammer afterwards to ensure they are tight.
      1. Note: If you don’t have a continuous 75′, such as two rolls of  50′ and 25′, plan it out first.  Cover the hoop, then back.  Save the front (door end) for last as it uses  3 smaller pieces.
    1. Cover the back and front sections and door with chicken wire.
      1. Note: the bottom 2′ will be hardware cloth and the upper section will be chicken wire.
        1. If you purchased 75′ you should be able to piece together the entire door and sides if you prefer.  I do the front and rear end across bottom with hardware cloth,  then the piece in the tops with the chicken wire.
    1. Surround the perimeter with 2′ hardware cloth.  I added this to stop predators from reaching in through the chicken wire and grabbing birds sleeping near the edge.
      1. Cover the back bottom 2′ that isn’t protected by your end material with  Hardware cloth.  Optionally you can cover the entire back for extra protection depending on what back end material you used.
      1. Start from the back and move to the front.
      1. Note:  If you don’t have 50′ continuous role, plan you’re cuts accordingly. IE, for 2 25′ roles, start in the back and wrap up to the door using one role for each side.  Then do the door.
    1. Add 2×4 fencing to ends.  This is added for K-9/coyote protection.  Three foot  doesn’t make it impossible for a K-9 to get over it, but that height with the chicken wire too makes for pretty good protection.  So far we’ve survived 2 K-9 attacks.
      1. Note:  Use a type/size predators cannot force through.  I use 2×4 3′ 14 gauge welded wire.
    1. Attach door with hinges and add latches and handle.
    1. Cover 2/3 of the hoop with the tarp, wrap extra around back.  Staple the tarp to the wood base and wire tie the eyelets to the hoop.
      1. Note:  My medium duty tarps last one season.  I remove and re-add each season.
    1. BONUS: Add an apron to the front and back for added protection.  You can also do the sides.
      1. Staple 12-14′ of 2′ hardware cloth to the front and back base, leaving 1-2′ of overlap past the tractor.  I try to leave it a little loose so it has a little “hinge” to it.   I don’t know that it’s required.
      1. Wire tie a PVC  pipe to opposite end of the hardware cloth for weight.
        1. Note:  If you cut the PVC end of the hardware cloth and bend the points down, it’s more of a deterrent for critters that might burrow under.

-Jason

 

Copyright © 2018 by Jason Maples

Dual-purpose Chickens – 10 – Moving the coop update

Jason Dual Purpose, Infrastructure, Layers, Poultry , , ,

In fall of 2014 I decided I wanted to raise some dual-purpose chickens.  My focus is on a breed that lays good eggs which can be incubated to raise “panfry” broilers, pre-Cornish-Cross size meat birds.  So how about an update on how I move the coop.

 

I tried to keep the size of the coop minimal so that it could be easily moved.  It’s still heavy and challenging to move.  My initial thought was to add permanent retractable wheels to one end and add some sort of a trailer type tongue to the other end for lifting an pulling.  Due to the weight, the tongue never happened.  Instead I still used the retractable wheels, but also put a sledge under the opposite “tongue” end and pulled it like a sled.

 

This wasn’t optimal.  The coop was too heavy for the retracting mechanism I made for the wheels.  It was also hard to lift the coop to put the sledge under the other end to drag it with.  Additionally, in the spring I had to use the tractor to move it because the garden tractor would get stuck, #1 The Coop.

So  I scrapped the contraption I made for the extendable wheels and  decided to use temporarily attached wheels instead.  I scavenged two more wheels from  the front of a dead riding lawn mower.  For axils, I use 8″ bolts that are the same diameter as the original wheel axils.  I drilled holes through the coop’s 4×4 bottom frame and just slide the wheels and bolds right on.  I added some spacers between the wheel and wood to prevent rubbing.

This works well.  Our winter area can get mucky, as you can probably tell by the picture to the right; however, the wheels still allow us to pull/push the coop by hand.  A small scrap piece of  chain added to one end helps us to pull or allows us to use the garden tractor for longer distance hauls.

 

The main downside of this method is that it requires at least two people to tip the coop and put the wheels on.  You could use a lever or jack to raise each side, but since I have two boys, it takes just a few minutes to tip the coop each way and add the wheels.

-Jason

Dual-purpose Chickens – 9 – Suplemental Light

Jason Dual Purpose, Infrastructure, Poultry , , , ,

In fall of 2014 I decided I wanted to raise some dual-purpose chickens.  My focus is on a breed that lays good eggs which can be incubated to raise “panfry” broilers, pre-Cornish-Cross size meat birds.  So, how do I provide supplemental light for consistent laying?

 

The 3 breeds I’ve raised so far,  Buff Orpingtons, Delaware, and Rainbows, are sensitive to the amount of “daylight” they get in relation to egg laying.  In the seasons when the days are shorter, they stop laying.  I’ve heard some breeds are not as sensitive and will keep laying, but these breeds slowed down and almost stopped on me before I added light to extend their “day”.

 

120Since I do want year round laying, I have to supplement the daylight with artificial light.   When the coop is near an electrical outlet, it’s easy enough to use a standard multi-time timer to power a CFL bulb in the coop.  However, we normally only bring the coop near an outlet in the cold part of winter and the birds still need supplemental light in the fall and spring when no outlets are near the coop.

 

 

 

toteTo solve this, I built a DC light box.  For the light,  I ordered a 12VDC LED bulb that plugs into a standard receptacle.  I took the plug off a hanging lamp and stripped the wires to attach them to unit.  I purchased a $10 DC timer that has 16 programmable on/off times.  And I alternate deep cycle batteries for the power supply.

 

I followed the instructions to hook up the timer; however, the switch on the timer wouldn’t handle the amperage of the light if I ran it through the timer switch.  So instead, I ran a car relay off the timer switch and wired the light through the relay.  I added a fuse in as well, mainly because I already had the female spade connector cramped on and also wanted an easy disconnect in that spot anyway.  It may not be pretty, but it works.

 

 

lightTo run the light into the coop, I disconnect the lamp wire and feed it through a hole I drilled in the coop and another hole in plastic tote that houses all the electronics.

This setup works pretty good.  I have two light cycles programed, one in the morning and another one at night.   I can get at least 5 days off one battery charge running 4-6 hours of light a day.  Below are the descriptions and links to the bulbs and timer I used for your reference.

-Jason

 

(Pack of 2) 5w E26 LED Bulbs, 12 Volt, Warm White, Round Shape, 40w Equivalent, Solar Powered LED Bulbs, Off Grid LED Bulbs

FAVOLCANO CN101 DC 12V 16A Digital LCD Power Programmable Timer Time Switch Relay

Dual-purpose Chickens – 8 – Winter Water

Jason Dual Purpose, Infrastructure, Layers, Poultry , , , , ,

In fall of 2014 I decided I wanted to raise some dual-purpose chickens.  My focus is on a breed that lays good eggs which can be incubated to raise “panfry” broilers, pre-Cornish-Cross size meat birds.  So, how do I keep the water from freezing?

One of banes of winter is frozen livestock water.  In the past, we’ve use 3 plastic 1 gallon waterers and rotated them throughout the day, bringing the frozen  ones in to thaw.  This was not an optimal solution.

 

I did some searching and was intrigued by an idea of using a tire to accumulate solar heat, and straw and a board inside the tire as insulation.  However, that would not work around here once the temperatures dropped well below freezing.

 

The idea I settled on was to use a concrete block with a light bulb inside, especially since the coop was going to be close to a power source.  It was easy to make.  Just an extension cord, a plugin light receptacle, a cooking tin, and a concrete block.  Put the cord, receptacle , and light bulb together and slid them into the concrete block.

base    light

To keep the block sitting level, either chisel a grove in the concrete block or sit the block on two pieces of wood and run the cord in-between the two pieced of wood.

Grove

And cover with a tin pan, to keep moisture away from the light.  Although I have metal waterers, I’m using the plastic ones as I think they handle the water freezing better.

waterer

I’m using a 60W bulb an it has worked pretty good.   So far this year,  most days stayed above 20 degrees , but  a few days were close to zero.  These days produced some frozen “rings” higher up in the waterer;  however, the tray stayed unfrozen and the chickens had unfrozen water to drink.    One thing to watch out for is that when the water gets close to being out, the waterer is lighter and easy to knocked off.

-Jason

Dual-purpose Chickens – 7 – What’s next?

Jason Dual Purpose, Layers, Poultry , , ,

rainbowIn fall of 2014 I decided I wanted to raise some dual-purpose chickens.  The main focus was on incubating my own birds to raise as “panfrys”, traditional meat birds frequently used in pan frying.  So where do I go from here?

 

So the questions I still have are what breed(s) do I want to continue working with and what size flock do I want.

 

 

For the breed, I’m not done trying different breeds.  I’m still looking for meet and eggs.  I’ve read that modern breeders are mostly focused on ‘show bird’  traits of the bird’s breed, and not on the functionality of the bird, such as egg production and size.  So, this year, I’m going to try buying my dual purpose birds from the hatchery I use for the meet birds.  The breed is called Rainbow and no two birds look alike.

 

As for the size of the flock, I’m still undecided for the long run.  A lot depends on where I want to go with these birds.  I think this year, I’ll stick to my a flock of 9-10 plus a rooster.  That way I won’t need to build a bigger coop.

 

The flock size brings us to the main question we get asked. “are you going to sell eggs”.  The answer is I don’t know.  It’s a possibility; however, this year it’s definitely going to be along the lines of a “when available” adjunct to us selling our chickens.  If we build a bigger coop, incorporate some egg only breed(s), and figure out some portable lighting for the coop, I’ll look more seriously at selling eggs in the future.

-Jason

Dual-purpose Chickens – 5 – Where’s the ‘beef’?

Jason Dual Purpose, Pastured, Poultry , , , , ,

In fall of 2014 I decided I wanted to raise some dual-purpose chickens.  The main focus was on incubating my own birds to raise as “panfrys”, traditional meat birds frequently used in pan frying.  So how did the “panfrys” do?

IMG_0435

They were good foragers, which IMHO adds to the taste.  I don’t have hard numbers on how much they foraged vs feed,  but they were very light on the feed compared to normal meat birds.

 

The birds were an average of 2lb dressed weight at 13 weeks and 3lb average dressed weight at 16.  That compares to the size of 1950s US Broiler Performance.  Next year I’ll try and get hard numbers on the feed ratio.

 

One limitation is that I averaged 20 chicks per incubation cycle.  Since I don’t do a lot of processing myself and the processing place is 70 miles away, it’s better to have larger quantities.  It’s feasible to raise two cycles together; however, to get a minimum of 3lb dressed weight, the older cycle will be 19 weeks old.  Roosters fights may be a problem at that age.

 

I plan on continuing research into the dual breeds for meat.  Three pounds is an ok size, especially for a tasty bird.  Hatching our own birds cuts out some costs and I’ll work harder next year to get good numbers on the feed ratios to determine what the actual costs per pound are.

-Jason

Chicken Tractor Plans – Part 2

Jason Brothers M., Chicken, Infrastructure, Pastured, Poultry , , , , ,

Just to add a little narrative on how I build the chicken tractors.

  1. Start with the 10×12′ frame.  The 10′ end pieces should raised slightly to help pull the tractor over clumps of grass.
  1. Add diagonal corner braces.  Not sure that size matters.
  1. Hoop 2 sections of cattle panels.  They will overlap slightly.
  1. Assemble the door.
  1. Cut the door frame and attach to base and hoop
  2. Put in rear vertical and diagonal supports.  Add something on the end bottom for additional shelter.  This will go to the most windward side, west for me.  Top is just covered by the tarp and can be raised for additional air flow.
  3. Cover the hoop with chicken wire, 3 passes of 4′.  Overlap slightly.
  1. Cover the ends & door with chicken wire.
  1. Surround the perimeter with 2′ hardware cloth (optional).  I do this to prevent predators from reaching in through the chicken wire and grabbing birds sleeping near the edge.
  1. Add 2×4 fencing to ends.  This is added to ensure K-9 type/size predators cannot force through chicken wire.
  2. Attach door and latches
  1. Cover 2/3 with tarp, wrap extra around back.

 

 

Copyright © 2018 by Jason Maples